氯化钼(III)

  • 基本信息
  • 制备方法及用途
  • 物化性质
  • 安全信息
  • 毒理性
  • MSDS
  • 结构与计算化学
  • 上游产品
  • 下游产品

氯化钼(III) 基本信息

中文名称:
氯化钼(III) 
中文别名:
三氯化钼;
氯化钼(III) 
英文名称:
Molybdenum chloride(MoCl3)
英文别名:
molybdenum trichloride;
EINECS 236-775-9;
trichloromolybdenum;
Molybdenum trichloride;
trichloridomolybdenum;
MoCl3 
CAS No.:
13478-18-7
分 子 式:
Cl3Mo
分 子 量:
202.30
精确分子量:
202.81200
PSA:
0.00000
MDL:
MFCD00014214
EINECS:
236-775-9
InChI:
InChI=1/3ClH.Mo/h3*1H;/q;;;+3/p-3
风险术语:
R36/37/38
安全术语:
S26S37/S39
分子结构式:
SDS:
查看

氯化钼(III) 制备方法及用途

合成制备方法

用金属钼和五氯化钼通过化学迁移反应进行合成。合成时,可使用如图所示的硼硅酸玻璃反应管。将直径为0.5mm的钼丝放入5中,加入的0.3g钼丝,仅相当于将反应管1、4处封闭时,每mL的容积加入0.3~06mg的量。往2处再加入0.2g的钼丝,然后用稀有气体置换反应管内的空气。从7处通入干燥氯气的同时,加热5处,则五氯化钼在2~3处析出。封闭1、6,用液氮冷却5处,使反应管内残存的氯气固化。随后封闭4处。将封管水平放置于由可独立控制温度的两部分组成的电炉中,使2处在450℃、3处在375℃下保持约10h,则于3处生成三氯化钼和四氯化钼的混合物。然后,使3处在400℃、2处在375℃下再保温10h,则在2处可得三氯化钼。最后,使2处于275℃、3处在室温下保温2~3h,以除去残存于2处的五氯化钼。要十分注意,所得的三氧化钼不可接触湿气,应在稀有气体或真空中进行处理。

                                          图VI-4   合成三氯化钼的反应管

除此以外,也可采用400℃下用氢气还原气态五氯化钼的方法或把四氯化钼置真空封管中,在约300℃下使之发生歧化反应的方法,这些方法均可制得三氯化钼。

氯化钼(III) 物化性质

蒸汽压:
33900mmHg at 25°C
存储条件/存储方法:

常温密闭,阴凉通风干燥惰性气体下

稳定性相关:

常温常压下稳定

避免的物料 水分/潮湿  空气  氧化物。

MoCl3有两种晶形,即Cl原子处于六方密堆积和立方密堆积的排列中,其中成对的钼原子穿过一共用边,处于相邻八面体空穴中,其间距为0.276nm。这说明了MoCl3中有MoMo键的存在,同时磁性的测定结果也与此相符。二聚离子[Mo2Cl9]3-呈抗磁性,并可能具有像[W2Cl9]3-那样的结构,即由两个共享一个面的畸变的MoCl6八面体组成,其中金属金属键矩较短,也说明了存在金属金属键。

当隔绝空气时这种暗红色的化合物是稳定的。它能被潮湿空气逐渐地水解和氧化。它不溶于水、稀盐酸、丙酮、四氯化碳和苯。它在乙醚、异丙醇和吡啶中有微小的溶解度,但是这个化合物能被稀硝酸完全溶解,或许是生成了某些更高度氧化的物种。差热分析研究表明氯化钼(Ⅲ)在温度高于410℃时歧化成MoCl2和MoCl4(冷却时生成MoCl3+MoCl5)[75],α-MoCl3和β-MoCl3的结构(两者都是单斜晶系的)都曾被确定过

其它信息:

1.       性状:紫铜色的单斜晶系结晶。

2.       密度(g/mL,25/4℃):3.74

3.       相对蒸汽密度(g/mL,空气=1):未确定

4.       熔点(ºC):未确定

5.       沸点(ºC,常压):未确定

6.       沸点(ºC,5.2kPa):未确定

7.       折射率:未确定

8.       闪点(ºC):未确定

9.       比旋光度(º):未确定

10.    自燃点或引燃温度(ºC):未确定

11.    蒸气压(kPa,25ºC):未确定

12.    饱和蒸气压(kPa,60ºC):未确定

13.    燃烧热(KJ/mol):未确定

14.    临界温度(ºC):未确定

15.    临界压力(KPa):未确定

16.    油水(辛醇/水)分配系数的对数值:未确定

17.    爆炸上限(%,V/V):未确定

18.    爆炸下限(%,V/V):未确定

19.    溶解性:分解

氯化钼(III) 安全信息

包装等级:
III
风险类别:
8
WGK_Germany:
3
德国有关水污染物质的分类清单
危险类别码:
R36/37/38
RTECS号:
QA4681400
安全标志:
S26:万一接触眼睛,立即使用大量清水冲洗并送医诊治。
:
危险标志:
Xi: Irritant;

氯化钼(III) 毒理性

CHEMICAL IDENTIFICATION

RTECS NUMBER :
QA4681400
CHEMICAL NAME :
Molybdenum chloride (MoCl3)
CAS REGISTRY NUMBER :
13478-18-7
LAST UPDATED :
199707
DATA ITEMS CITED :
2
MOLECULAR FORMULA :
Cl3-Mo
MOLECULAR WEIGHT :
202.29

HEALTH HAZARD DATA

ACUTE TOXICITY DATA

MUTATION DATA

TEST SYSTEM :
Insect - Drosophila melanogaster
DOSE/DURATION :
10 mmol/L
REFERENCE :
MUREAV Mutation Research. (Elsevier Science Pub. B.V., POB 211, 1000 AE Amsterdam, Netherlands) V.1- 1964- Volume(issue)/page/year: 320,133,1994
毒理学数据:

1、急性毒性:主要的刺激性影响:

在皮肤上面:在皮肤和粘膜上造成腐蚀性影响,刺激皮肤和粘膜;

在眼睛上面:强烈的腐蚀性影响,刺激的影响;没有已知的敏化影响。

生态数据:

通常对水体是稍微有害的,不要将未稀释或大量产品接触地下水,水道或污水系统,未经政府许可勿将材料排入周围环境。

氯化钼(III) MSDS


Section 1: Product Identification
   Chemical Name:       Molybdenum(III) chloride (99.5%-Mo)    
   CAS Registry Number:       13478-18-7    
   Formula:       MoCl3    
   EINECS Number:       236-775-9    
   Chemical Family:       metal halide    
   Synonym:       Molybdenum trichloride    

Section 2: Composition and Information on Ingredients
   Ingredient       CAS Number       Percent       ACGIH (TWA)       OSHA (PEL)    
   Title Compound       13478-18-7       100%       0.5mg/m3       5mg/m3    

Section 3: Hazards Identification
   Emergency Overview:       Corrosive to skin, eyes and respiratory tract. Inhalation of dust leads to burning of the respiratory tract.    
   Primary Routes of Exposure:       Contact with skin and eyes. Inhalation of dust.    
   Eye Contact:       Corrosive to the eyes.    
   Skin Contact:       Causes burns to the skin.    
   Inhalation:       Inhalation of dust leads to chemical burns of the respiratory tract.    
   Ingestion:       No information is available on the physiological effects of ingestion.    
   Acute Health Affects:       Corrosive to skin, eyes and respiratory tract.    
   Chronic Health Affects:       No information available on long-term chronic effects.    
   NTP:       No    
   IARC:       No    
   OSHA:       No    

SECTION 4: First Aid Measures
   Immediately flush the eyes with copious amounts of water for at least 10-15 minutes. A victim may need
   Eye Exposure:
   assistance in keeping their eye lids open. Get immediate medical attention.
   Wash the affected area with water. Remove contaminated clothes if necessary. Seek medical assistance if
   Skin Exposure:
   irritation persists.
   Remove the victim to fresh air. Closely monitor the victim for signs of respiratory problems, such as difficulty
   Inhalation:
   in breathing, coughing, wheezing, or pain. In such cases seek immediate medical assistance.
   Seek medical attention immediately. Keep the victim calm. Give the victim water (only if conscious). Induce
   Ingestion:
   vomiting only if directed by medical personnel.

SECTION 5: Fire Fighting Measures
   Flash Point:       not applicable    
   Autoignition Temperature:       none    
   Explosion Limits:       none    
   Extinguishing Medium:       none required    
   If involved in a fire, fire fighters should be equipped with a NIOSH approved positive pressure self-contained
   Special Fire Fighting Procedures:
   breathing apparatus and full protective clothing.
   Hazardous Combustion and       none    
   Decomposion Products:
   Unusual Fire or Explosion Hazards: No unusual fire or explosion hazards.

SECTION 6: Accidental Release Measures
   Small spills can be neutralized with powdered sodium bicarbonate, lime, or calcium carbonate and swept up.
   Spill and Leak Procedures:       Large spills in areas not adequately ventilated will require an evacuation of site. Emergency response teams    
   will require self-contained breathing apparatus.

SECTION 7: Handling and Storage
   Handling and Storage:       Store material in a tightly sealed container under an inert atmosphere of nitrogen or argon.    

SECTION 8: Exposure Controls and Personal Protection
   Eye Protection:       Always wear approved safety glasses when handling a chemical substance in the laboratory.    
   Skin Protection:       Wear protective clothing gloves. Consult glove manufacturer to determine the proper type of glove.    
   Ventilation:       If possible, handle the material in an efficient fume hood.    
   If in form of fine dust and ventilation is not available a respirator should be worn. The use of respirators
   Respirator:
   requires a Respirator Protection Program to be in compliance with 29 CFR 1910.134.
   Ventilation:       If possible, handle the material in an efficient fume hood.    
   Additional Protection:       No additional protection required.    

SECTION 9: Physical and Chemical Properties
   Color and Form:       -100 mesh purple xtl.    
   Molecular Weight:       202.32    
   Melting Point:       dec.    
   Boiling Point:       no data    
   Vapor Pressure:       no data    
   Specific Gravity:       3.59    
   Odor:       none    
   Solubility in Water:       reacts with water    

SECTION 10: Stability and Reactivity
   Stability:       air sensitive, moisture sensitive    
   Hazardous Polymerization:       no hazardous polymerization    
   Conditions to Avoid:       contact with moisture    
   Incompatibility:       active metals    
   Decomposition Products:       none    

SECTION 11: Toxicological Information
   RTECS Data:       Oral (insect-Drosophila melanogaster); Specific locus test: 10nmol/L.    
   Carcinogenic Effects:       no data    
   Mutagenic Effects:       Mutagen    
   Tetratogenic Effects:       no data    

SECTION 12: Ecological Information
   Ecological Information:       No information available    

SECTION 13: Disposal Considerations
   Disposal:       Dispose of according to local, state and federal regulations.    

SECTION 14: Transportation
   Shipping Name (CFR):       Corrosive solids, N.O.S.    
   Hazard Class (CFR):       8    
   Additional Hazard Class (CFR):       NA    
   Packaging Group (CFR):       II    
   UN ID Number (CFR):       UN# 1759    
   Shipping Name (IATA):       Corrosive solid, N.O.S.    
   Hazard Class (IATA):       8    
   Additional Hazard Class (IATA):       NA    
   Packaging Group (IATA):       II    
   UN ID Number (IATA):       UN# 1759    

SECTION 15: Regulatory Information
   TSCA:       Listed in the TSCA inventory.    
   SARA (Title 313):       Title compound not listed    
   Second Ingredient:       none    


SECTION 16 - ADDITIONAL INFORMATION
N/A

氯化钼(III) 分子结构与计算化学数据

分子结构数据

1、摩尔折射率:无可用的

2、摩尔体积(cm3/mol):无可用的

3、等张比容(90.2K):无可用的

4、表面张力(dyne/cm):无可用的

5、介电常数:无可用的

6、极化率(10-24cm3):无可用的

7、单一同位素质量:202.811965 Da

8、标称质量:203 Da

9、平均质量:202.299 Da

计算化学数据

1.疏水参数计算参考值(XlogP):无

2.氢键供体数量:0

3.氢键受体数量:0

4.可旋转化学键数量:0

5.互变异构体数量:无

6.拓扑分子极性表面积0

7.重原子数量:4

8.表面电荷:0

9.复杂度:8

10.同位素原子数量:0

11.确定原子立构中心数量:0

12.不确定原子立构中心数量:0

13.确定化学键立构中心数量:0

14.不确定化学键立构中心数量:0

15.共价键单元数量:1

氯化钼(III) 下游产品

推荐供应商更多供应商>>