硫化铼(VII)单水合物

  • 基本信息
  • 制备方法及用途
  • 物化性质
  • 安全信息
  • 毒理性
  • MSDS
  • 结构与计算化学

硫化铼(VII)单水合物 基本信息

中文名称:
硫化铼(VII)单水合物 
中文别名:
硫化铼;
一水合硫化铼 硫化铼一水合物 
英文名称:
dirhenium heptasulphide
英文别名:
RHENIUM HEPTASULFIDE;
rheniumsulfide(re2s7);
dirhenium heptasulphide;
RHENIUM(VII) SULFIDE 
CAS No.:
12038-67-4
分 子 式:
Re2S7
分 子 量:
614.89
精确分子量:
597.71600
PSA:
217.84000
MDL:
MFCD00211312
EINECS:
234-882-5
安全术语:
S24/25
分子结构式:
SDS:
查看

硫化铼(VII)单水合物 制备方法及用途

制备方法

1.于20~80℃下往Re2O7中通入硫化氢。2.取过量的硫化钠加到高铼酸钾水溶液中,再加入浓盐酸及硫酸铵,配制成约6mol/L盐酸酸性混合液后,煮沸之,Re2S7则沉淀出来,将该溶液冷却至室温,过滤,洗涤后进行真空干燥。3.取1g市售的高铼酸钾粉碎后,溶于100mL左右热稀盐酸(10%)中,往该溶液中通入硫化氢,则七硫化二铼以细粉状黑色沉淀析出,沉淀凝聚后,在隔绝空气下,过滤,先用硫化氢水溶液洗涤,接着用水洗涤,将沉淀先在真空中于140℃下加热2h,接着在P2O5上于165~170℃下干燥(以Abdelhalden干燥器为宜)。

合成制备方法

1.于20~80℃下往Re2O7中通入硫化氢。

2.取过量的硫化钠加到高铼酸钾水溶液中,再加入浓盐酸及硫酸铵,配制成约6mol/L盐酸酸性混合液后,煮沸之,Re2S7则沉淀出来,将该溶液冷却至室温,过滤,洗涤后进行真空干燥。

3.取1g市售的高铼酸钾粉碎后,溶于100mL左右热稀盐酸(10%)中,往该溶液中通入硫化氢,则七硫化二铼以细粉状黑色沉淀析出,沉淀凝聚后,在隔绝空气下,过滤,先用硫化氢水溶液洗涤,接着用水洗涤,将沉淀先在真空中于140℃下加热2h,接着在P2O5上于165~170℃下干燥(以Abdelhalden干燥器为宜)。

用途简介

硫化铼(VII)单水合物 物化性质

密度:
4.866 g/mL at 25 °C(lit.)
蒸汽压:
12600mmHg at 25°C
存储条件/存储方法:

常温密闭,阴凉通风干燥

稳定性相关:

常温常压下稳定

避免的物料 氧化物。因在空气中易于氧化,故过滤等操作应在隔绝空气下进行。对于盐酸或硫酸等如在无空气条件下,也不能溶解。如接触空气时,则被氧化生成高铼酸而溶解。接触氧化剂(如Br2、H2O2等)也是如此,能吸附甲苯等而膨润。

其它信息:

1.       性状:粉末

2.       密度(g/mL,25℃):4.866

3.       相对蒸汽密度(g/mL,空气=1):未确定

4.       熔点(ºC):未确定

5.       沸点(ºC,常压):未确定

6.       沸点(ºC,1mmHg):未确定

7.       折射率:未确定

8.       闪点(ºC):未确定

9.       比旋光度(º):未确定

10.    自燃点或引燃温度(ºC):未确定

11.    蒸气压(20ºC):未确定

12.    饱和蒸气压(kPa,60ºC):未确定

13.    燃烧热(KJ/mol):未确定

14.    临界温度(ºC):未确定

15.    临界压力(KPa):未确定

16.    油水(辛醇/水)分配系数的对数值:未确定

17.    爆炸上限(%,V/V):未确定

18.    爆炸下限(%,V/V):未确定

19.    溶解性:未确定

硫化铼(VII)单水合物 安全信息

WGK_Germany:
3
德国有关水污染物质的分类清单
安全说明:
S24/25
安全标志:
S24/25:防止皮肤和眼睛接触。

硫化铼(VII)单水合物 毒理性

生态数据:

通常对水是不危害的,若无政府许可,勿将材料排入周围环境

硫化铼(VII)单水合物 MSDS

Name: Rhenium Heptasulfide 99% Material Safety Data Sheet
Synonym: Rhenium (VII) Sulfide
CAS: 12038-67-4
Section 1 - Chemical Product   MSDS Name:Rhenium Heptasulfide 99% Material Safety Data Sheet
Synonym:Rhenium (VII) Sulfide

Section 2 - COMPOSITION, INFORMATION ON INGREDIENTS
CAS# Chemical Name content EINECS#
12038-67-4 Rhenium Heptasulfide 99% 234-882-5
Hazard Symbols: None Listed.
Risk Phrases: None Listed.

Section 3 - HAZARDS IDENTIFICATION
  EMERGENCY OVERVIEW
The toxicological properties of this material have not been fully investigated.Air sensitive.
Potential Health Effects
Eye:
May cause eye irritation. The toxicological properties of this material have not been fully investigated.
Skin:
May cause skin irritation. The toxicological properties of this material have not been fully investigated.
Ingestion:
May cause irritation of the digestive tract. The toxicological properties of this substance have not been fully investigated.
Inhalation:
May cause respiratory tract irritation. The toxicological properties of this substance have not been fully investigated.
Chronic:
No information found.

Section 4 - FIRST AID MEASURES
  Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and drink 2-4 cupfuls of milk or water. Wash mouth out with water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid.
Notes to Physician:

Section 5 - FIRE FIGHTING MEASURES
  General Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion. Use extinguishing media appropriate to the surrounding fire. Substance is noncombustible.
Extinguishing Media:
Substance is noncombustible; use agent most appropriate to extinguish surrounding fire. Use agent most appropriate to extinguish fire. Use water spray, dry chemical, carbon dioxide, or appropriate foam.

Section 6 - ACCIDENTAL RELEASE MEASURES
  General Information: Use proper personal protective equipment as indicated in Section 8.
Spills/Leaks:
Vacuum or sweep up material and place into a suitable disposal container. Clean up spills immediately, observing precautions in the Protective Equipment section. Avoid generating dusty conditions.
Provide ventilation. Place under an inert atmosphere.

Section 7 - HANDLING and STORAGE
  Handling:
Wash thoroughly after handling. Use with adequate ventilation.
Minimize dust generation and accumulation. Avoid breathing dust, vapor, mist, or gas. Avoid contact with eyes, skin, and clothing.
Keep container tightly closed. Avoid ingestion and inhalation.
Handle under an inert atmosphere. Store protected from air.
Storage:
Store in a tightly closed container. Keep under a nitrogen blanket.
Store in a cool, dry, well-ventilated area away from incompatible substances. Do not expose to air. Store under an inert atmosphere.

Section 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
  Engineering Controls:
Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate ventilation to keep airborne concentrations low.
Exposure Limits CAS# 12038-67-4: Personal Protective Equipment Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to prevent skin exposure.
Respirators:
Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced.

Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
 
Physical State: Powder
Color: black
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: Not available.
Autoignition Temperature: Not applicable.
Flash Point: 600 deg C ( 1,112.00 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature: 600 deg C
Solubility in water: insoluble
Specific Gravity/Density: 4.8660g/cm3
Molecular Formula: Re2S7
Molecular Weight: 596.84

Section 10 - STABILITY AND REACTIVITY
  Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, dust generation, exposure to air, excess heat.
Incompatibilities with Other Materials:
Oxidizing agents.
Hazardous Decomposition Products:
Oxides of sulfur, irritating and toxic fumes and gases, hydrogen sulfide.
Hazardous Polymerization: Has not been reported.

Section 11 - TOXICOLOGICAL INFORMATION
  RTECS#:
CAS# 12038-67-4 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Rhenium Heptasulfide - Not listed by ACGIH, IARC, or NTP.

Section 12 - ECOLOGICAL INFORMATION
 

Section 13 - DISPOSAL CONSIDERATIONS
  Dispose of in a manner consistent with federal, state, and local regulations.

Section 14 - TRANSPORT INFORMATION
 
IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

Section 15 - REGULATORY INFORMATION
 
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: Not available.
Risk Phrases:
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
S 28A After contact with skin, wash immediately with
plenty of water.
S 37 Wear suitable gloves.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 12038-67-4: 2
Canada
CAS# 12038-67-4 is listed on Canada's NDSL List.
CAS# 12038-67-4 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 12038-67-4 is listed on the TSCA inventory.


SECTION 16 - ADDITIONAL INFORMATION
N/A

硫化铼(VII)单水合物 分子结构与计算化学数据

计算化学数据

1、   氢键供体数量:0

2、   氢键受体数量:7

3、   可旋转化学键数量:0

4、   拓扑分子极性表面积(TPSA):0

5、   重原子数量:9

6、   表面电荷:-14

7、   复杂度:0

8、   同位素原子数量:0

9、   确定原子立构中心数量: 0

10、   不确定原子立构中心数量:0

11、   确定化学键立构中心数量:0

12、   不确定化学键立构中心数量:0

13、   共价键单元数量:9

推荐供应商更多供应商>>

山东西亚化学有限公司

产品介绍:
产品名称:硫化铼 Cas号:12038-67-4 纯度:98% 包装信息:1g 价格:670.0元
联系方式:
联系人:崔 电话:4009903999 手机:18053972095

山东默派生物科技有限公司

产品介绍:
产品名称:硫化铼 Cas号:12038-67-4 纯度:99% 包装信息:1kg 价格:洽谈
联系方式:
联系人:张经理 电话:13070690626 手机:13070690626

湖北恩星生物科技有限公司

产品介绍:
产品名称:硫化铼 Cas号:12038-67-4 纯度: 包装信息:100kg,200kg,300kg,400kg,500kg 价格:64.0元 - 100.0元
联系方式:
联系人:邵经理 电话:16621771607 手机:16621771607

上海一基实业有限公司

产品介绍:
产品名称:硫化铼 Cas号:12038-67-4 纯度: 包装信息:洽谈 价格:洽谈
联系方式:
联系人:张嘉彬 电话:021-60536261 17802116021 手机:17802116021

阿法埃莎(天津)化学有限公司

产品介绍:
产品名称:硫化铼(VII)单水合物 Cas号:12038-67-4 纯度: 包装信息:洽谈 价格:洽谈
联系方式:
联系人:张海滨 电话:800-810-6000 手机: